Thread: Problem With My Box

  1. #1
    Registered User
    Join Date
    Sep 2005
    Posts
    15

    Angry Problem With My Box

    My mom told me to take a look at her computer for cuz it would start up. Ok I figure this would be easy ! Oh was I wrong, I thought it might of been the power plugs were loose or fell out on the mother board. Apperently not So could anyone here possibly help me out with this ? I mean the computer wont even start period and im just about to take the memory and the hard drive and just shove it in my box in my room!


    Sorry that I haven't provided that much information here its just that i really have no idea whats wrong with it.
    Last edited by HaVoX; 10-13-2005 at 09:35 PM.

  2. #2
    Registered User
    Join Date
    Sep 2004
    Location
    California
    Posts
    3,268
    Does anything appear on the screen at all? Does the power supply even turn on when you press the power button? If the power supply does turn on, is there any beeps coming from the PC speaker?

  3. #3
    Registered User VirtualAce's Avatar
    Join Date
    Aug 2001
    Posts
    9,607
    No video signal - no green light on monitor
    • Video card problem - possible short in VGA connector or connector loose
    • Monitor problem - possible short in VGA connector
    • Short in VGA cable


    No POST, no video but green light, no beeps from computer:
    • IDE cables plugged in backwards - some early ones were not 'keyed' and could be plugged in backwards.
    • One or more RAM modules are seated incorrectly or not at all.
    • If you have 1 RAM module, most boards require it to be in RAM slot 1
    • Incompatible memory types - mixing EECs with non - EECs.
    • One or more RAM modules are defective
    • Dust on the RAM modules is causing a direct short somewhere. This dust is most often from the CPU fan since most RAM slots are located very near the CPU socket.


    POST and beeps
    • Check the number of beeps in the board's manual to find out the problem. Generally, one beep is either a keyboard error, hard drive error (can't find the boot drive), or floppy error. Floppy drive cables can be plugged in backwards which will cause the red light to stay lit. This will cause the drive to be unresponsive to any commands coming from the BIOS which will flag an error.
    • 3 beeps - video card error. Video card is either being shorted out by dust on the card, is not seated properly, or has an on-board problem causing the 2D circuitry to be unreponsive to BIOS POST.


    No power, no lights, no spin ups on hard drives - no responses
    • Short inside of the power supply - a lot of stress is put on these power cables in order to reach many of the devices in the case. Often times these power cables will short out near the exit from the power supply and/or completely detach from the power supply motherboard. Check all power connections to all devices and ensure that the female and male plugs are connected correctly and solidly. Often times the metal tabs holding a wire in the plastic plug will break causing a bad connection to occur when mated with it's female counterpart. Replace these immediately - these can and will cause a hard drive to reset if they short out and will certainly result in lost data and/or a dead drive.
    • Modern power supplies have a breaker built into them. When this breaker has been overloaded it trips and does not allow power to get to the motherboard. This can be reset by simply flipping the switch on the back of the power supply to zero instead of 1. Unplug the computer from the outlet or power strip and wait for a couple of minutes. Plug the system back in and turn the power supply to one, and turn the system on. The system should start. One sure sign of an overloaded and tripped power supply breaker is a flashing green power light or a flashing power light on the case. This indicates an overload has occurred.
    • The power supply has burned up either due to age, excessive heat, and/or a massive power surge. If it is because of the latter you can bet there will be some fried components in the computer including but not limited to: video card, sound card, LAN card, CPU, CPU chipset, keyboard circuitry, etc. Basically anything that was plugged into the motherboard at the time of the surge.
    • Onboard video is interfering with a 3rd party video card. Sometimes this causes an unresponsive system. Remove the video card and reboot. Go into the BIOS of the system and turn the onboard video off. Turn the system off. Plug in the video card into PCI slot 1 or AGP slot 1. If it is a PCI card, the video card must be plugged into PCI slot 1.
    • Onboard video card (if equipped) has a problem. Purchase a 3rd party video card (NVidia or ATI), turn the onboard video off (via the system BIOS), install the new card, turn the system on, and install the new drivers inside of Windows using the CD that came with the card.


    If you get absolutely no response from the system and you have checked that power is indeed getting to the power supply, my best estimation is that the internal power supply breaker has been tripped due to an overload, a sudden power outage, or a sudden spike in the line. This breaker is designed to protect your motherboard and if it has tripped then you can probably be assured that none of your components have been damaged.

    If this is a video problem it is because the card is not taking interrupt 10h and the BIOS recognizes this serious problem and simply halts the system. The video card if it is a PCI or older ISA card must be in slot 1. Any other slot will not work. There can only be one 2D card in the system at any time. There can, however, be more than one 3D accelerator in the system. In the past card manufacturers would create cards that were simply 3D accelerators and nothing more. These cards do not take interrupt 10h and therefore can be installed along with a normal 2D video card (provided the drivers and hardware are compatible with the 2D card). The old 3DFx Voodoo series cards used to do this. This practice has since been discontinued, but when working on other people's computers - you can come across pretty much anything and everything.


    Troubleshooting steps
    • Get down to a bare bones system.
    • Unplug all unnecessary devices from the motherboard.
    • You probably will only have the CPU, memory, and video card (if you don't have onboard video) in the system.
    • Turn the system on.
    • If it works, then gradually one by one plug in a new card or new device and turn the system on.
    • Repeat this process until the system becomes unresponsive. This is essentially process of elimination. This will identify for you which card or device is causing the problem.
    Last edited by VirtualAce; 10-14-2005 at 12:46 AM.

  4. #4
    Registered User
    Join Date
    Sep 2005
    Posts
    15
    No theres no response at all...like I said it doesnt turn on lol meanign when I press that button nothing happens

  5. #5
    Registered User
    Join Date
    Sep 2004
    Location
    California
    Posts
    3,268
    Is there a switch on the back of your power supply? If so, make sure it is turned to the "on" position. Also make sure that if the computer is plugged into a surge protector, you have the surge protector turned on.

    Also, try plugging the computer into a different outlet. If you still can't get it working, then the problem is probably either the power supply, or the motherboard.

  6. #6
    C++ Enthusiast jmd15's Avatar
    Join Date
    Mar 2005
    Location
    MI
    Posts
    532
    On my old computer it had problems with the fan and powerpack and did the same thing. It wouldn't start up, and it sounds like it's the powerpack. Since that computer was Windows ME we just got a new computer instead. The fan also wasn't working on that computer, and I noticed that when it got hot enough the computer shut itself off and wouldn't turn back on until I turned off the surge protector, waited 2 minutes, and then turned it all back on. So the fan could be doing it. I'm pretty sure it is the powerpack though.
    Trinity: "Neo... nobody has ever done this before."
    Neo: "That's why it's going to work."
    c9915ec6c1f3b876ddf38514adbb94f0

  7. #7
    Registered User
    Join Date
    Sep 2005
    Posts
    15
    So basically what I'm gathering here from all your great responses is that my computer is just trashed and isnt worth fixing(to much money for me neway) Well i guess I'm gonna just take some stuff out of there to put into my box....





    >YES I LOVE UPGRADES!!!!!!<

  8. #8
    C++ Enthusiast jmd15's Avatar
    Join Date
    Mar 2005
    Location
    MI
    Posts
    532
    Well a new powerpack isn't too much money, around $25-30(I think, not too sure). That sounds like your problem.
    Trinity: "Neo... nobody has ever done this before."
    Neo: "That's why it's going to work."
    c9915ec6c1f3b876ddf38514adbb94f0

  9. #9
    It's full of stars adrianxw's Avatar
    Join Date
    Aug 2001
    Posts
    4,829
    Does sound like the power supply. They are not that expensive, but cheap power supplies are a bad investment, get a decent one, an Antec or similar.

    >>> to much money for me neway

    It is your mothers machine, you should not have to pay for it.
    Wave upon wave of demented avengers march cheerfully out of obscurity unto the dream.

  10. #10
    Registered User
    Join Date
    Sep 2005
    Posts
    15
    >>> to much money for me neway
    It is your mothers machine, you should not have to pay for it.
    Yea thats true but her and my dad are both the same they try to blame everything with the computer on me even though I wasnt there the weekend it happened!?!?! Its really funny how my computers in my room are perfectly fine and I have nothing wrong with them but I somehow manage to ruin theres when i dont even go on them? well w/e!


    Is there anything you would recomend me getting?

Popular pages Recent additions subscribe to a feed

Similar Threads

  1. Annoying Message Box Problem
    By Necrofear in forum C++ Programming
    Replies: 14
    Last Post: 07-02-2006, 11:25 AM
  2. message box and unicode problem
    By Jumper in forum Windows Programming
    Replies: 2
    Last Post: 05-11-2004, 02:53 PM
  3. Replies: 5
    Last Post: 12-03-2003, 05:47 PM
  4. Dialog Edit box v's WindowsText Problem
    By simham_uk in forum Windows Programming
    Replies: 2
    Last Post: 06-10-2002, 07:28 AM
  5. Ihave a problem with an EDIT box..
    By SyntaxBubble in forum Windows Programming
    Replies: 1
    Last Post: 10-30-2001, 09:25 AM