Thread: Amd64 has arrived at my house!! Woot!

  1. #1
    1479
    Join Date
    Aug 2003
    Posts
    253

    Amd64 has arrived at my house!! Woot!

    I got a new mobo with amd 64 processor in today. The heatsink comes with a thermal interfact material pre-applied, and the heatsink came with the processor. My question is, will I still have to apply thermal grease?
    Knowledge is power and I want it all

    -0RealityFusion0-

  2. #2
    Redundantly Redundant RoD's Avatar
    Join Date
    Sep 2002
    Location
    Missouri
    Posts
    6,331
    You should wipe that crap off, and wet sand the block on a level surface to ensure a level, even finish. Then use Arctic Silver 3 or 5 and mount it.

  3. #3
    5|-|1+|-|34|) ober's Avatar
    Join Date
    Aug 2001
    Posts
    4,429
    Good God... don't do that unless you really know what you're doing. Often the factory stuff should work ok.

  4. #4
    PC Fixer-Upper Waldo2k2's Avatar
    Join Date
    May 2002
    Posts
    2,001
    I agree.

    By sanding down the heatsink you can seriously affect it's performance, you'd have a better chance burning up your proc by doing that than just leaving the factory standard stuff there.
    PHP and XML
    Let's talk about SAX

  5. #5
    Redundantly Redundant RoD's Avatar
    Join Date
    Sep 2002
    Location
    Missouri
    Posts
    6,331
    Eh, proper lapping and performance compound can make night and day differences in performance and reliability.

  6. #6
    PC Fixer-Upper Waldo2k2's Avatar
    Join Date
    May 2002
    Posts
    2,001
    well if you think it's that big of a concern, he should just buy a seperate heatsink and put compound on it himself, rather than mess with the one he has and possibly screw things up...
    PHP and XML
    Let's talk about SAX

  7. #7
    Cat without Hat CornedBee's Avatar
    Join Date
    Apr 2003
    Posts
    8,895
    The factory-supplied fan and heat paste on my Athlon64 is VERY loud (sounds like a vacuum cleaner), but still fails to sufficiently cool the PC under high load if the room temperature rises above ~26 degrees Celsius.

    So, if you know what you're doing, I'd say get a better cooling system. If not (like me), leave the stuff that works and make sure your room stays cool, for yourself as much as your PC.
    All the buzzt!
    CornedBee

    "There is not now, nor has there ever been, nor will there ever be, any programming language in which it is the least bit difficult to write bad code."
    - Flon's Law

  8. #8
    5|-|1+|-|34|) ober's Avatar
    Join Date
    Aug 2001
    Posts
    4,429
    No offense.... but thermal paste cannot be "loud".

  9. #9
    Cat without Hat CornedBee's Avatar
    Join Date
    Apr 2003
    Posts
    8,895
    *sigh* I knew someone would post this.

    Ok, here's the version for the pedantic.
    The factory-supplied cooling equipment, consisting of a fan, a cooling block and a patch of thermal paste, is not ideal in that the fan is too loud and the combination fails to keep the CPU temperature below 73°C (the default temperature at which the BIOS will refuse to boot) if the room temperature, and thus the temperature of the air that is used for cooling, rises above approximately 26°C, which it often does during summer in my room.

    Happy now?

    Besides, you have no idea just HOW loud thermal paste can be...
    All the buzzt!
    CornedBee

    "There is not now, nor has there ever been, nor will there ever be, any programming language in which it is the least bit difficult to write bad code."
    - Flon's Law

  10. #10
    Redundantly Redundant RoD's Avatar
    Join Date
    Sep 2002
    Location
    Missouri
    Posts
    6,331
    Most "assembly line" heat sinks from the OEM are not even or "level" and therefore do not properly dissipate heat across the cpu. Lapping fixes this, and the use of an aftermarket paste such as AC5, can get u about 3-5 degree's cooler just fom the paste.

  11. #11
    PC Fixer-Upper Waldo2k2's Avatar
    Join Date
    May 2002
    Posts
    2,001
    why not just buy an oem processor and a seperate heatsink? that's what I usually do.
    PHP and XML
    Let's talk about SAX

  12. #12
    Cat without Hat CornedBee's Avatar
    Join Date
    Apr 2003
    Posts
    8,895
    I believe that wasn't even possible in my case with the Athlon64. At least not where I was buying.
    All the buzzt!
    CornedBee

    "There is not now, nor has there ever been, nor will there ever be, any programming language in which it is the least bit difficult to write bad code."
    - Flon's Law

  13. #13
    PC Fixer-Upper Waldo2k2's Avatar
    Join Date
    May 2002
    Posts
    2,001
    where did you buy it???
    cause that's friggin rediculous
    PHP and XML
    Let's talk about SAX

  14. #14
    Cat without Hat CornedBee's Avatar
    Join Date
    Apr 2003
    Posts
    8,895
    It's a small country I live in. There were no bulk versions available, only the packaged ones. And those come with a heatsink and fan.
    All the buzzt!
    CornedBee

    "There is not now, nor has there ever been, nor will there ever be, any programming language in which it is the least bit difficult to write bad code."
    - Flon's Law

  15. #15
    PC Fixer-Upper Waldo2k2's Avatar
    Join Date
    May 2002
    Posts
    2,001
    you can order out of country you know...unless austria has some sort of outrageous import tax/law? But anyways I'm sorry to hear that you have limited options.
    PHP and XML
    Let's talk about SAX

Popular pages Recent additions subscribe to a feed

Similar Threads

  1. I hate Dr. House!
    By Mario F. in forum A Brief History of Cprogramming.com
    Replies: 11
    Last Post: 10-02-2006, 06:27 AM
  2. Expendable house program, please help
    By ademkiv in forum C Programming
    Replies: 3
    Last Post: 02-21-2006, 06:49 AM